Build Desk
Why Your Lower Back Hurts When You Deadlift (and How to Keep Pulling)
Lower back pain on deadlifts is one of the most common reasons men stop pulling — and one of the most fixable. If your back aches during the lift or the next morning, it rarely means you have broken something. Most of the time it means the hinge, your brace, or the load grew faster than your back could handle, and the fix is smarter technique, a lighter rebuild, and patience. This guide covers why deadlifts hurt the lower back, the form faults behind most of it, how to rebuild the lift safely, and the warning signs that mean a physio or doctor should take a look.
What deadlift back pain usually is
Deadlift back pain usually comes down to load versus tolerance — how much stress your lower back took against how much it was ready for. The deadlift loads the spine more than any other lift, and a systematic review in BMJ Open Sport & Exercise Medicine (2024) found the lower back and pelvis are the most commonly injured areas in powerlifting, at 1 to 4 injuries per 1,000 hours of training. That does not mean your back is broken. Most deadlift back pain is a hinge, bracing, or load problem — and those respond to changing how you lift, not to giving the lift up.
The five faults behind most of it
Most deadlift back pain traces to one of five faults, and most lifters are making at least one. First, squatting the lift — hips too low, knees too far forward — turns a hinge into a squat. Second, losing the brace: the trunk goes soft mid-pull and the spine rounds. Third, the bar drifting away from the shins, which multiplies the load on the lower back. Fourth, adding weight too fast, the same load mistake behind our knee pain when squatting piece. Fifth, fatigue in late sets, when form slips rep by rep. Film a heavy set from the side and you will see which fault is yours.
Fix the hinge first
The deadlift is a hip hinge, not a squat, and the hinge is worth drilling. Stand tall, push your hips back until your hands reach your knees, and keep your shins close to vertical — your knees bend a little, but the movement comes from the hips. Practice with a light bar or a broomstick along your spine: it should touch the back of your head, your upper back, and your tailbone the whole way down. If the stick lifts off your tailbone, you are rounding. A few minutes of hinge practice before your next pull, plus our stretching guide for hip mobility, changes how the lift feels.
Brace before every rep
A brace is what keeps your spine stiff while the bar moves, and it has to happen before the pull starts, not halfway up. Take a breath into your belly, tighten your trunk as if someone is about to poke you in the stomach — then pull. Reset and re-brace between reps instead of touch-and-go sets while you rebuild; bouncing the bar off the floor hides a lost brace. A lifting belt can help you push against something on heavy sets, but it is a cue, not a fix — if you cannot brace without one, the belt is covering a gap. Breathe, brace, pull, every single rep.
Keep the bar close and the load honest
The bar should start over the middle of your foot, drag up your shins, and stay close to lockout — every inch it drifts forward adds leverage against your lower back. Wear long socks if the bar scrapes, and do not step away from the bar between reps. Load matters just as much: our progressive overload guide explains why small jumps beat big ones, and a 10 lb jump on a 185 lb pull is over 5 percent. Add weight in 5 lb steps, and when form slips in late sets, stop the set — grinding out ugly reps is how backs get hurt.
The rebuild: lighter, higher, patient
If your back hurts every time you pull, stop chasing your old numbers and rebuild. Drop the weight by 20 to 30 percent and earn it back in small jumps — a 315 lb puller rebuilds from around 225 lb. Raise the bar while you rebuild: block pulls, with the bar starting a few inches higher, cut the hardest part of the lift and let you groove the hinge pain-free. Keep training through it — staying active beats bed rest for most back pain — and if a lighter week is due, our deload week guide and rest and recovery guide show how to run one.
Red flags and when to see a physio or doctor
Most deadlift back pain improves with a lighter load, a better hinge, and a real brace, but some signs mean stop and get checked promptly. See a physio or doctor if pain shoots down your leg, or you feel numbness, tingling, or weakness in a leg or foot. Worsening pain over days, pain that wakes you at night, a fever, or an inability to bear weight also need a clinician's eyes — those are not technique problems. This article is general information, not medical advice: if any of these apply, book the appointment before your next pull. Your back has to last longer than any single training block.
What to look for
- Lifting belt — A belt gives you something to brace against on heavy sets — a cue for a stronger brace, not a substitute for one.
- Trap bar — A trap bar lets you pull with a more upright torso, which takes some load off the lower back while you rebuild your hinge.
- Lifting shoes with a raised heel — A raised heel helps if stiff ankles are changing your pull — the same fix that helps squats can help your deadlift setup.
Common questions
Is lower back pain normal when deadlifting?
Some soreness after a hard pull is common, but sharp pain during the lift, or pain that lingers for days, is not something to train through. Most deadlift back pain comes from the hinge, the brace, or the load growing too fast — all fixable. Drop the weight by 20 to 30 percent, rebuild the hinge, and see whether it settles. Pain that shoots down the leg, or comes with numbness or weakness, is a reason to see a physio promptly. This article is general information, not medical advice.
Should I stop deadlifting if my lower back hurts?
Usually not completely. Most lifters do better dropping the load by 20 to 30 percent, raising the bar with block pulls, and keeping moving than stopping entirely — staying active beats bed rest for most back pain. Stop and get checked if pain shoots down your leg, you feel numbness, tingling, or weakness, the pain keeps worsening, or it wakes you at night. Our deload week guide shows how to run a lighter week when one is due.
Does a lifting belt stop lower back pain when deadlifting?
A belt can help you brace harder, which protects the spine on heavy sets — but it does not fix a bad hinge, a bar that drifts away from your shins, or weight added too fast. Think of it as a cue, not treatment. The changes that actually help are usually the hinge, the brace, the bar path, and the load. If a belt lets you pull with good form at a sensible weight, it is doing its job.
When should I see a doctor about lower back pain from deadlifting?
Book an appointment if pain shoots down your leg, or you have numbness, tingling, or weakness in a leg or foot; if the pain keeps worsening over several days; if it wakes you at night; if you have a fever; or if you cannot bear weight. Also see a clinician if the pain keeps returning despite lighter loads and form fixes. This article is general information, not medical advice, and a physio can check your back and your lift in person.
More from the Build desk
Protein Guide: How Much You Actually Need
The complete protein guide — the evidence for 1.6-2.2 g/kg, gram counts for everyday foods, vegetarian sources, and the truth about whey.
BuildCreatine: The One Supplement With Real Evidence (and the Hair-Loss Question)
An honest guide to creatine monohydrate — the 3-5 g dose, why loading is optional, the single DHT study behind the hair-loss worry, and buying safely.
BuildYour First 8 Weeks in the Gym: A Beginner Plan That Actually Works
Your first 8 weeks of training — compound lifts, a simple 3-day full-body structure, the progressive overload rule, and the mistakes every beginner makes.